Beko Washer F13 usually points to a drying fan or fan-circuit fault on washer-dryer models, or a communication problem related to the fan monitoring circuit on the main PCB. The single most likely fix is to inspect and reconnect the fan wiring harness, then test the fan motor for continuity before replacing a failed fan assembly.
Start with a full reset. Unplug the washer, leave it disconnected for 15 to 30 minutes, then restore power and restart a cycle. This clears temporary PCB logic faults and may remove the code if the issue was caused by a brief voltage spike or software lockup.
The most common real fix is checking the drying fan circuit. Remove the top or rear access panel, inspect the fan connector, and make sure the wiring harness is seated firmly with no burned terminals, loose pins, or corrosion. If the fan is jammed, noisy, or open-circuit on a multimeter, replace it.
If the code returns, move to deeper diagnosis. Test the fan motor winding, inspect the harness back to the control board, and check the PCB for damaged relay tracks, swollen capacitor failure, or heat marks around the fan drive circuit. At that point, professional board-level diagnosis may be the fastest repair.
On a Beko Washer F13 fault, the control system is detecting an abnormal condition in the drying fan circuit or in the feedback the board expects from that circuit. This code is most commonly seen on Beko washer-dryer units rather than wash-only machines, because the fan is used to move air during the drying process and sometimes during cooling phases. If the PCB cannot power the fan, cannot detect normal fan operation, or sees electrical values outside range, it stores F13 and may stop the cycle.
Technically, the problem can come from several points in the circuit. The fan motor itself may be seized, electrically open, or drawing too much current. The wiring harness may have a broken conductor, overheated connector, or poor contact at the terminal. Less often, the main control board, relay section, or fan driver components on the PCB fail and prevent proper voltage from reaching the fan.
Because the control board monitors operating conditions closely, F13 can also appear after an interrupted drying cycle, moisture-related electrical issues, or power fluctuation. A simple reset is worth trying first, but if the code comes back consistently, a component in the fan circuit usually needs inspection and electrical testing.
The fan motor is the most common cause of F13 on a Beko washer-dryer. Bearings can seize from lint buildup or moisture, and the winding can fail electrically, causing the PCB to detect no rotation or incorrect current draw.
A partially disconnected plug, broken wire, or overheated terminal between the fan and the control board can interrupt the circuit. Even if the fan itself is good, high resistance in the harness can stop the motor from starting properly and trigger the error.
If the PCB cannot switch power to the fan, the machine may report F13 immediately or when the drying stage begins. Burned relay contacts, cracked solder joints, and failed board components such as a capacitor or driver transistor are realistic causes.
Lint, debris, or a warped fan blade can physically prevent the fan from spinning at normal speed. The motor may hum, overheat, or stall, and the control board interprets that as a fan circuit failure.
Washer-dryers operate in a humid environment, and moisture can affect low-voltage connectors and PCB tracks over time. Corrosion on terminals can create intermittent fan operation, especially if the error appears only during drying cycles.
Follow the steps below one at a time — many error codes can be fixed faster than they look.
Tools you may need: screwdriver, multimeter, flashlight
Safety warning: Disconnect power before opening any panels or touching internal components.
Perform the reset first. Unplug the washer for at least 15 minutes, then plug it back in and try a short program or a drying function if your model has one. If F13 clears and does not return, the fault may have been a temporary control board logic issue rather than a hard component failure.
Access the fan area. On most Beko washer-dryer units, this requires removing the top panel and sometimes the rear panel to reach the drying fan assembly and its wiring. Use a flashlight to look for lint accumulation, melted plastic around the connector, signs of overheating, or a fan impeller that does not turn freely by hand.
Inspect the wiring harness carefully. Unplug the fan connector and check for loose pins, green corrosion, arcing marks, or damaged insulation along the harness route back to the PCB. Reseat each connector firmly and repair or replace any damaged wiring before testing the appliance again.
Test the fan motor with a multimeter. With power disconnected and the fan isolated from the harness, check continuity across the motor terminals; an open circuit usually indicates a failed winding, while a dead short suggests internal motor damage. If the fan blades are stiff, scraping, or seized, replace the fan assembly even if continuity seems present.
Check for supply voltage during the fan call if you are qualified to do live testing safely. If the control board sends power to the fan but the motor does not run, the fan is faulty. If there is no output from the board when the machine enters drying mode, the issue is likely in the PCB, relay, or control circuit rather than the motor itself.
Inspect the main control board. Look for burnt spots, cracked solder joints, failed relay contacts, or swollen capacitors near the fan drive section. If you see visible PCB damage, board repair or replacement is usually more reliable than trying repeated resets.
Reassemble the washer and run a test cycle. Start with a short drying-related program if available and monitor for normal fan sound and airflow. Stop and call a professional if you find board damage, if live voltage tests are required and you are not trained, or if the error returns after the fan and harness have already tested good.
Yes. Unplug the appliance for 15 to 30 minutes, then reconnect power and restart the machine. If the F13 code was caused by a temporary PCB glitch or power interruption, that may clear it. If the code returns during drying or shortly after startup, the fan circuit likely has a real hardware fault.
No. If F13 is related to the fan motor or fan control circuit, continuing to run the machine can lead to overheating, repeated cycle failure, or additional PCB stress. It is better to stop using the drying function immediately and diagnose the fault before it damages other components.
No. The main control board is only one possible cause. A failed fan motor, blocked fan housing, damaged wiring harness, or corroded connector is often more common and less expensive to fix. Always test the fan and wiring first before replacing a PCB.
Cost depends on what failed. A simple connector repair or wiring repair is usually the lowest-cost fix, while a fan motor replacement is moderate. A control board repair or replacement is typically the most expensive option. The exact total also depends on labor, access time, and whether your Beko washer is a washer-dryer model.
Yes. On washer-dryer units, lint and debris can obstruct the fan blade or airflow path enough to stall the motor or increase current draw. The PCB may then register abnormal fan performance and show F13. Cleaning the fan area is a smart early step before condemning electrical parts.
Call a professional if the fan tests good but there is no board output, if you see burnt PCB components, or if live electrical testing is needed and you are not trained to do it safely. Professional diagnosis is also recommended when the machine repeatedly shows F13 after reset and harness inspection.
Try these recommended tools — used by thousands to solve the same issue:
As an Amazon Associate / affiliate partner we may earn from qualifying purchases.
Browse More Fixes